Nylon Chemical Resistance: Acids, Bases, Solvents, Automotive Fluids, and Food Contact
Chemical resistance is the single most misunderstood property of nylon in engineering procurement. Most engineers treat “nylon” as a single material when assessing chemical compatibility, then are surprised when PA6 and PA12 behave dramatically differently in the same environment.
This guide provides systematic chemical resistance data for PA6, PA66, and PA12 across all major chemical classes, with clear guidance on when nylon is appropriate and when alternative materials should be specified.
Understanding Nylon Chemical Resistance Mechanisms
Nylon resistance to chemicals operates through three distinct mechanisms. Understanding which mechanism applies to your environment determines whether the material will perform reliably.
Physical resistance: The polymer matrix physically blocks chemical penetration. This is the dominant mechanism for non-polar solvents like gasoline and oils — nylon has excellent resistance because hydrocarbon molecules cannot penetrate the crystalline domains.
耐薬品性: The polymer chain does not react with the chemical. This is why nylon is attacked by strong acids and bases — they hydrolyze the amide bonds in the polyamide chain.
Plasticization and swelling: Water and polar solvents penetrate the amorphous regions, swelling the polymer without breaking chemical bonds. This increases flexibility but reduces stiffness and dimensional accuracy.
| Chemical Class | PA6 | PA66 | PA12 | Primary Mechanism | Application Notes |
|---|---|---|---|---|---|
| Motor oils (mineral) | 素晴らしい | 素晴らしい | 素晴らしい | Physical barrier | Under-hood auto applications |
| Motor oils (synthetic) | 素晴らしい | 素晴らしい | 素晴らしい | Physical barrier | ATS, DCT fluids |
| Gasoline (aromatic) | Good (60°C) | Good (100°C) | 素晴らしい | Physical barrier | Fuel rails: PA66-GF30 |
| Ethanol blends (E85) | Limited | Limited (80°C) | 素晴らしい | Physical + swelling | Fuel lines: PA12 preferred |
| Diesel, Biodiesel | グッド | グッド | 素晴らしい | Physical barrier | Fuel system components |
| ATF / Transmission fluid | Good (120°C) | Excellent (150°C) | グッド | Physical barrier | Transmission oil pans |
| Glycol coolant (50/50) | Good (100°C) | Good (130°C) | 素晴らしい | Swelling (limited) | Coolant reservoirs |
| Brake fluids (DOT 3/4/5) | 貧しい | 貧しい | グッド | Chemical attack | Use PA12 for brake components |
| Weak acids (<10%) | Limited (elev T) | Limited (elev T) | グッド | Chemical hydrolysis | PA12 or PP for acid contact |
| Strong acids (>10%) | Not recommended | Not recommended | Limited | Rapid hydrolysis | PVDF or PTFE for acid |
Water Absorption and Its Effect on Chemical Resistance
Moisture absorption fundamentally changes nylon’s chemical resistance profile. Dry nylon is more chemically resistant to polar solvents (the plasticized, wet state actually resists further polar penetration) but is more susceptible to oxidative degradation. This creates a critical design consideration: parts in wet service should be tested in the conditioned (wet) state, not dry-as-molded.
| Conditioning State | PA6 Tensile Strength | PA6 Modulus | Chemical Resistance to Water | Chemical Resistance to Acids |
|---|---|---|---|---|
| Dry as molded (0%) | 85 MPa | 3,200 MPa | 該当なし | Poor (brittle failure) |
| Conditioned 50% RH (2.5%) | 65 MPa | 2,000 MPa | 中程度 | Moderate (ductile) |
| Saturated (9.0%) | 45-50 MPa | 1,200 MPa | Swells significantly | Moderate (ductile) |
| After drying (0.1%) | 80+ MPa | 3,000 MPa | 素晴らしい | Poor (brittle failure) |
Industrial and Laboratory Chemical Environments
For chemical processing and industrial equipment, verify compatibility under actual operating conditions with immersion testing. The following table provides baseline guidance for common industrial chemicals.
| Chemical | PA6 | PA66 | PA12 | Max Service Temp (°C) | Alternative Material |
|---|---|---|---|---|---|
| Sulfuric acid (10%) | Limited | Not recommended | Limited | 40°C | PVDF, HDPE |
| Hydrochloric acid (10%) | Not recommended | Not recommended | Limited | 40°C | PVDF, PTFE |
| Sodium hydroxide (50%) | Limited (>60°C) | Not recommended | グッド | 80°C | PP, HDPE |
| Acetone | Limited | Not recommended | グッド | 60°C | PTFE |
| Ethanol | グッド | グッド | 素晴らしい | 100°C | PA12 preferred |
| Phenol (5%) | Not recommended | Not recommended | Not recommended | 該当なし | PTFE only |
| Formic acid (10%) | Not recommended | Not recommended | Limited | 40°C | PTFE, PVDF |
| Calcium chloride | Limited | Limited | グッド | 80°C | PA12 for salt contact |
| Steam (continuous) | Not recommended | Not recommended | Limited | 120°C | PPS, PTFE |
Automotive Fluids: The Most Common Real-World Exposure
Automotive under-hood applications define the largest volume of nylon use globally. The following data reflects ASTM D543 immersion testing results at specified temperatures and exposure durations (typically 1,000 hours = approximately 6 weeks of continuous exposure).
| Fluid | PA6 | PA66 | PA12 | Weight Change | Tensile Retention | Application Confidence |
|---|---|---|---|---|---|---|
| Engine oil SAE 5W-30 (150°C) | 素晴らしい | 素晴らしい | 素晴らしい | <1% | >95% | Full production use |
| Transmission fluid ATF (130°C) | グッド | 素晴らしい | グッド | <2% | >90% | Full production use |
| Power steering fluid (120°C) | グッド | グッド | 素晴らしい | <2% | >90% | Full production use |
| Coolant 50/50 EG (130°C) | グッド | グッド | 素晴らしい | <3% | >85% | Full production use |
| Brake fluid DOT 4 (120°C) | 貧しい | 貧しい | グッド | >10% | <60% | PA12 only |
| Windshield washer (60°C) | 素晴らしい | 素晴らしい | 素晴らしい | <0.5% | >99% | Full production use |
| Battery acid (25°C) | Not recommended | Not recommended | Not recommended | 該当なし | 該当なし | PP or PE only |
| AdBlue / DEF (urea) | グッド | グッド | 素晴らしい | <1% | >95% | SCR system components |
よくあるご質問
How do you know whether Nylon Chemical Resistance: Acids, Bases, Solvents, and More fits a part?
Nylon Chemical Resistance: Acids, Bases, Solvents, and More fits a part when its load capacity, temperature range, moisture exposure, wear behavior, and processing method match the real service conditions.
What properties should be checked for Nylon Chemical Resistance: Acids, Bases, Solvents, and More?
強度、剛性、耐衝撃性、耐熱性、吸湿性、寸法安定性、摩擦、摩耗、および化学的適合性を確認する。.
What is the biggest selection risk for Nylon Chemical Resistance: Acids, Bases, Solvents, and More?
最大のリスクは、実際の使用環境、加工方法、部品の形状、および長期使用を考慮せずに、データシートの数値だけで選定してしまうことです。.
When should Nylon Chemical Resistance: Acids, Bases, Solvents, and More be tested before production?
部品が荷重、熱、化学物質、湿気、厳しい公差、規制要件、あるいは新たな動作環境にさらされる場合は、試験を行うことをお勧めします。.
