PA6 GF40 | 40% ガラス繊維によって補強されるナイロン6 -ナイロンプラスチック

PA6 GF40とは?

PA6 GF40は、ポリアミド6(ナイロン6)を40%ガラス繊維で強化したエンジニアリングプラスチック複合材です。この強化により、機械的強度、剛性、耐熱性が大幅に向上するとともに、吸湿と熱膨張が減少します。.

ナイロン樹脂のPA6 GF40を選ぶ理由

✅ 一貫した品質:厳格な品質管理でバッチ間の信頼性を確保

✅ 技術的専門知識:材料の選択から生産まで、フル・エンジニアリング・サポート

✅ カスタムソリューション:特定の用途に合わせた処方

✅ 迅速な配達:試作から量産までの信頼できるサプライチェーン

カテゴリー: , ブランド:
PA6 GF40 glass-fiber-reinforced nylon 6 material overview

PA6 GF40 Material and Grade Overview

PA6 GF40 is nylon 6 reinforced with 40% glass fiber for injection-molded parts that need higher stiffness and load capacity than lower-glass PA6 grades. The exact grade still matters: heat stabilization, impact modification, color, moisture conditioning and test conditions can change the final result.

  • Use it for: structural housings, brackets and equipment parts where rigidity and dimensional control are important.
  • Check before approval: load, temperature, moisture, impact, surface requirements, fiber orientation and warpage.
  • For purchasing: confirm the grade-specific TDS, required documents, quantity and destination before quotation.

PA6 WHG40A Datasheet Values

The values below come from the WanHan PA6 WHG40A technical data sheet supplied through the manufacturer download center.

プロパティ 代表値 テスト基準
引張強度 185 MPa ISO 527-2
曲げ弾性率 8,500 MPa ISO 178
エイチディーティー 180°C ISO 75-2/B
密度 1.44 g/cm³ ISO 1183

These are typical material values, not finished-part guarantees. The source PDF does not state specimen conditioning; confirm the current TDS and test conditions for the selected formulation.

Download the PA6 WHG40A datasheet (PDF)  |  Request a matching grade or sample

Choose PA6 GF40 Against the Part Requirement

Glass content is one selection input, not the full specification. Compare the reinforcement level against mold filling, fiber orientation, surface, impact and dimensional requirements.

  • PA6 GF30: review when the part can meet its stiffness target with lower reinforcement and easier processing.
  • PA6 GF40: review when higher rigidity is needed and the mold, gate and part geometry can control fiber orientation and warpage.
  • PA6 GF50: evaluate only after checking flow, weld lines, appearance and tooling requirements.

「」を使用してください。 PA6 selection page to compare the wider grade range.

PA6 GF40 Performance Advantages

High Stiffness-to-Weight Potential

PA6 GF40は、非常に高い引張強度と曲げ弾性率を含む優れた機械的特性を備えており、高荷重と高応力に耐えなければならない構造部品に適しています。.

Thermal Performance by Exact Grade

The heat deflection temperature depends on the final PA6 GF40 formulation, conditioning and ISO 75 test conditions. Confirm the grade-specific TDS and molded-part performance before approving a high-temperature application.

Dimensional Control with Design Review

Glass reinforcement can improve dimensional stability, but PA6 still responds to moisture and fiber orientation. Check conditioning, gate direction and the installed environment before assigning close tolerances.

Chemical and Wear Performance to Be Verified

Chemical and wear suitability depends on the exact compound, mating surface, load, speed and exposure. Review the medium and operating conditions against the selected grade data before approval.

Injection Molding and Part-Design Checks

  • Drying and moisture: follow the selected grade TDS and verify moisture before molding; do not apply a generic setting to every PA6 GF40 compound.
  • Gate and fiber orientation: gate position and flow direction affect stiffness, shrinkage, weld lines and warpage.
  • Wall and transition design: keep wall changes practical and review ribs, bosses and radii for stress concentration and filling.
  • Part validation: approve dimensions and performance on molded parts under the intended conditioning and service environment.

PA6 GF40 Applications

Injection-molded PA6 GF40 applications for automotive and industrial parts

PA6 GF40 is considered for structural automotive, electrical and industrial parts when high rigidity is required. Surface appearance, electrical rating and heat performance must be confirmed for the selected grade.

Typical Application Directions

産業 主な用途
自動車 エンジンカバー、インテークマニホールド、構造用ブラケット、センサーハウジング、コネクター。.

自動車への応用を探る

電気・電子 サーキットブレーカー、スイッチ、コネクターハウジング、絶縁部品.

E&Eソリューションの発見 → E&Eソリューションの発見

産業機器 ギア、ベアリング、機械ハウジング、ローラー、機械部品。.

工業用を参照 →工業用

PAプラスチックの様々な応用シーン
PAプラスチックの様々な応用シーン

PA6 GF40 Supply and Project Support

PA6 GF40 material production and quality control

PA6 GF40 granules and manufacturing support

PA6 GF40 Questions

Q: What does the WHG40A 180°C HDT value mean?
A: It is the typical value reported under ISO 75-2/B (0.45 MPa). Do not compare it directly with data measured at a different load or conditioning state.

Q: What should be checked before choosing GF40 over GF30?
A: Verify stiffness and deflection on the actual part, then check flow, fiber orientation, warpage, surface finish and moisture conditioning. Higher glass content alone does not approve a part.

Request PA6 GF40 TDS, Sample or Quote

For grade selection, send the operating temperature, load, moisture or chemical exposure, color and required documents. For a quotation, add the order quantity, annual volume, destination and target timing.

サンプル、スケジュール、および書類: 条件を満たすプロジェクトについては、無料サンプルをご用意しております。標準グレード製品の製造には通常5~7日、カスタム配合の場合は通常2~3週間かかります。選択されたグレードについて、材料仕様書および該当する認証書をご提供可能です。在庫状況および対応範囲については、技術チームにご確認ください。.

Tell Us About Your Part

このフィールドは必須です。.
このフィールドは必須です。.
このフィールドは必須です。.
このフィールドは必須です。.
このフィールドは必須です。.
このフィールドは必須です。.
このフィールドは必須です。.
トップに戻る

連絡先

下記のフォームにご記入ください。.

連絡先