PA6 GF30 | 30% ガラス繊維によって補強されるナイロン6 -ナイロンプラスチック

PA6 GF30とは何ですか?

PA6 GF30は、ポリアミド6(ナイロン6)に30%ガラス繊維を強化材として配合したエンジニアリングプラスチック複合材です。この強化により、機械的強度、剛性、耐熱性が大幅に向上するとともに、吸湿性と熱膨張率が低減されます。.

なぜナイロン・プラスチックのPA6 GF30を選ぶべきなのか?

✅ 一貫した品質:厳格な品質管理でバッチ間の信頼性を確保

✅ 技術的専門知識:材料の選択から生産まで、フル・エンジニアリング・サポート

✅ カスタムソリューション:特定の用途に合わせた処方

✅ 迅速な配達:試作から量産までの信頼できるサプライチェーン

カテゴリー: , ブランド:

Exact-Grade Datasheet Reference: PA6 WHG30A

Typical values from the WanHan “PA6 GF30.pdf” datasheet for grade WHG30A: tensile strength 165 MPa (ISO 527-2), flexural modulus 6,000 MPa (ISO 178), heat deflection temperature 175°C (ISO 75-2/B, 0.45 MPa), and density 1.36 g/cm³ (ISO 1183).

このPDFには試験片の調整条件が記載されていません。衝撃試験の行には「アイゾット」と記載されていますが、引用されているのはシャルピー試験の規格であるISO 179ですので、その値を使用する前に試験方法を確認してください。 PDFに記載されているISO 75-2/BのHDT値は、一連の表にある1.8 MPaの数値の代替として使用することはできません。これらは代表的な材料値であり、完成品の保証値ではありません。選択した配合について、最新のPDFおよび試験条件を請求してください。.

Request PA6 GF30 TDS / Quote

万翰详情 01

PA6 GF30 Series Property Ranges

These ranges are illustrative across formulations and test conditions; they are not the grade-specific values of PA6 WHG30A. Use the matching datasheet and molded-part tests for approval.

プロパティ 価値 テスト基準
ガラス繊維含有量 30% ISO 1172
引張強度 125~175 MPa ISO 527
曲げ弾性率 5,218~8,500 MPa ISO 178
衝撃強度  12~17 kJ/m² ISO 180
熱偏向温度 165~190°C(1.8MPa) ISO 75
融点 215~230°C ISO 3146
水分吸収 ~1.8% ISO 62

PA6シリーズ材料性能比較表:

プロパティ PA6 GF15 PA6 GF30 PA6 GF40 PA6 GF50 PA6 GF60
ガラス繊維含有量 15% 30% 40% 50% 60%
密度 (g/cm³) 1.21 1.38 1.46 1.56 1.67
引張強さ (MPa) 118 165 185 200 220
破断伸度(%) 3.3 3.0 2.8 2.0 2.0
ノッチ付き衝撃強さ (kJ/m²) 10 12 13 14 14
熱たわみ温度 (℃, 1.8MPa) 160 175 215 216 220

Choosing PA6 GF30 for Your Part

PA6 GF30 contains 30% glass fiber by weight. It is a common starting point when an unfilled or lower-filled grade does not meet stiffness or dimensional requirements. Fiber orientation, moisture conditioning, mold design and surface finish still need review for the actual part.

For more retained toughness or a less reinforced surface, compare PA6 GF15. For a higher stiffness target, review PA6 GF40 and its processing trade-offs. See the PA6 selection page for the wider range.

Share the current grade or TDS, application, service temperature, moisture or chemical exposure, required properties, color and requested documents. A drawing is optional for a material-only inquiry, and estimated usage may be stated as “Not sure yet”.

Request PA6 GF30 TDS / Quote
Need PA6 GF30 Molded Parts?

主な長所:(中略

✅ 優れた強度重量比

PA6 GF30は、金属並みの強度を持ちながら重量はわずかしかなく、性能を損なうことなく軽量設計を実現します。.

✅ 高い耐熱性

Heat deflection depends on the exact formulation, conditioning and ISO 75 method. Compare the matching grade datasheet and test molded parts at the intended service temperature.

✅ 優れた寸法安定性

吸湿性が低く、熱膨張も最小限に抑えられているため、さまざまな環境条件下でも安定した性能を発揮します。.

✅ 良好な耐薬品性

油類、燃料、および多くの化学物質に対して優れた耐性を示し、自動車や産業用途に最適です。.

 

産業への応用:

自動車産業における射出成形の重要な役割

PA6 GF30は、良好な表面仕上げと基本的な剛性を必要とする自動車部品、内装部品、その他の用途に一般的に使用されています。.

業界を超えたイノベーションの原動力

産業 主な用途
自動車 エンジンカバー、インテークマニホールド、構造用ブラケット、センサーハウジング、コネクター。.

自動車への応用を探る

電気・電子 サーキットブレーカー、スイッチ、コネクターハウジング、絶縁部品.

E&Eソリューションの発見 → E&Eソリューションの発見

産業機器 ギア、ベアリング、機械ハウジング、ローラー、機械部品。.

工業用を参照 →工業用

PAプラスチックの様々な応用シーン
PAプラスチックの様々な応用シーン

どう選ぶ?

わかりやすく言えば、"ヴェニュー "である:

  • について タフネス または 費用対効果, と考える。 PA6 GF15.

  • について 総合的にバランスの取れたパフォーマンス, を選択する。 PA6 GF30.

  • について より高い剛性、強度、耐熱性, また、コストにあまり敏感でない場合は、次のように考える。 PA6 GF40/50/60. .一般に、ガラス繊維の含有率が高いほど、これらの特性は向上する。.

当社を選ぶ理由

万翰详情 03

万翰详情 04

PA6 GF30 Questions

Q: Is the 190°C figure the HDT of WHG30A?
A: No. The WHG30A PDF gives a typical HDT of 175°C under ISO 75-2/B (0.45 MPa). The 165–190°C range above is a general illustration with a different stated condition; confirm the exact grade and test load for approval.

Q: Should I use GF15 or GF40 instead?
A: Compare GF15 if lower reinforcement may satisfy the load while retaining the desired finish or toughness. Compare GF40 if the part still needs higher stiffness; check fiber orientation, warpage and molded-part results.

サンプル、スケジュール、および書類: 条件を満たすプロジェクトについては、無料サンプルをご用意しております。標準グレード製品の製造には通常5~7日、カスタム配合の場合は通常2~3週間かかります。選択されたグレードについて、材料仕様書および該当する認証書をご提供可能です。在庫状況および対応範囲については、技術チームにご確認ください。.

Tell Us About Your Part

このフィールドは必須です。.
このフィールドは必須です。.
このフィールドは必須です。.
このフィールドは必須です。.
このフィールドは必須です。.
このフィールドは必須です。.
このフィールドは必須です。.
トップに戻る

連絡先

下記のフォームにご記入ください。.

連絡先