プラスチック射出成形におけるSPI表面仕上げ規格:完全ガイド

SPI表面仕上げ規格とは何ですか?

SPI(Society of the Plastics Industry、現PLASTICS Industry Association)の表面仕上げ基準は、金型キャビティの研磨レベルを指定するための世界共通の基準となっています。 数十年前、製品設計者と金型メーカー間のコミュニケーションを標準化するために導入されたSPIシステムでは、表面仕上げをA、B、C、Dの4つのグレードに分類し、各グレードには3つのサブレベルが設けられています。グレードAは最高光沢のダイヤモンド研磨面を表し、グレードDは粗いブラスト仕上げの質感を示します。 世界中の有能な金型メーカーは皆、これらの指定を理解しており、SPIは射出成形のサプライチェーン全体において、技術図面、見積依頼書、品質検査報告書における標準的な参照システムとなっています。

A1の鏡面光沢からD3のマット仕上げまで、SPIの表面仕上げグレードを示す6枚の射出成形ナイロン製プレート
A1の鏡面光沢からD3のマット仕上げまで、SPIの表面仕上げグレードを示す6枚の射出成形ナイロン製プレート

仕上げ仕様を適切に決定することは、外観、離型、金型加工、およびメンテナンスに影響を与えます。 高光沢仕上げとブラスト仕上げでは作業内容が異なりますが、そのコストやメンテナンス間隔は、金型用鋼材、面積、アクセス性、形状、樹脂、および生産条件によって異なります。グレード表を用いて仕上げ仕様を伝えた上で、定義された表面ゾーンおよび承認済みのサンプルや測定要件に基づいて見積もりを依頼してください。

機械工が、ロータリーツールにダイヤモンド研磨剤を塗布して、射出成形金型のキャビティを手作業で研磨している
機械工が、ロータリーツールにダイヤモンド研磨剤を塗布して、射出成形金型のキャビティを手作業で研磨している

SPI グレードA:ダイヤモンド研磨仕上げ

Aグループの仕上げでは、粒度が徐々に細かくなるダイヤモンド化合物を使用します。仕上がりは、工具鋼、初期表面状態、形状、および研磨のしやすさによって異なります。表面粗さや外観の許容要件については、SPI指定とは別途に合意してください。また、指定された樹脂および色で成形されたサンプルを確認してください。

Aグレードの仕上げについては、外観と光学性能を区別し、研磨可能な箇所、キャビティの形状、鋼材の状態、および将来のメンテナンスについて確認してください。再研磨は重要寸法に影響を与える可能性があるため、仕上げ作業後の金型および成形サンプルの検査方法について合意しておいてください。 A-1およびA-2については、一律の価格プレミアムやサービス間隔ではなく、実際の光学性能または外観要件に基づいて比較してください。

SPIグレードB:上質な半光沢仕上げ

グレードBの仕上げでは、ダイヤモンドコンパウンドの代わりに研磨紙を使用し、ほとんどの一般消費者向け部品に適した半光沢の表面を実現します。B-1では600番の研磨紙を使用し、Ra 0.05~0.10 μmを実現し、 B-2では400番の紙を使用しRa 0.10~0.15 μm、B-3では320番の紙を使用しRa 0.15~0.28 μmを実現します。 これらは射出成形における主力となる仕上げであり、消費者向け製品の金型キャビティの約60%がB-1またはB-2仕上げで出荷されています。この半光沢の外観は、Aグレード仕上げでは目立ってしまうようなわずかなフローライン、ブラッシュマーク、シンクを隠しつつ、ほとんどの消費者の期待を満たす高級感ある外観を実現しています。

Bグループの加工には研磨紙を使用します。必要な外観および承認された基準に基づき粒度を選択し、研磨面積、キャビティ数、およびメンテナンス費用を個別に提示してください。仕上げ指定のみでは、固定の割増料金やショット数を保証することはできません。

SPIグレードCおよびD:テクスチャ仕上げおよびマット仕上げ

Cグループの表面処理には研磨石を使用し、Dグループの表面処理にはドライブラストを使用します。各サブグレードにおいて、基準となる研磨材の粒度は粗くなります。これらの説明は金型の表面処理に関するものです。成形品の外観は、樹脂、充填剤、色、および加工方法によっても異なります。部品の表面粗さが保証されていると推測するのではなく、参照用の表面処理ガイドおよび承認済みのサンプルを使用してください。

テクスチャ加工された表面は、確実に離型させるために、より大きな抜き勾配が必要になる場合があります。テクスチャの深さ、刻み方向、金型の形状、樹脂の種類、および金型メーカーの推奨事項を総合的に検討してください。Dグレードのテクスチャすべてに一律の角度を追加することは避け、生産用金型を切削する前に、離型性と外観の問題を解決しておいてください。

SPI指定 準備に関する参考資料 購入要件
A-1 ダイヤモンド化合物、グレード3 基準サンプルおよび別途必要とされるRaについて合意する。
A-2 ダイヤモンド化合物、グレード6 基準サンプルおよび別途必要とされるRaについて合意する。
A-3 ダイヤモンドコンパウンド、グレード15 基準サンプルおよび別途必要とされるRaについて合意する。
B-1 紙、600番 基準サンプルおよび別途必要とされるRaについて合意する。
B-2 紙、400番 基準サンプルおよび別途必要とされるRaについて合意する。
B-3 紙、320番 基準サンプルおよび別途必要とされるRaについて合意する。
C-1 ストーン、600番 基準サンプルおよび別途必要とされるRaについて合意する。
C-2 ストーン、400番 基準サンプルおよび別途必要とされるRaについて合意する。
C-3 ストーン、320番 基準サンプルおよび別途必要とされるRaについて合意する。
D-1 ガラスビーズによるドライブラスト 基準サンプルおよび別途必要とされるRaについて合意する。
D-2 酸化物ドライブラスト、240番 基準サンプルおよび別途必要とされるRaについて合意する。
D-3 酸化物ドライブラスト、24グレード 基準サンプルおよび別途必要とされるRaについて合意する。

以下の準備グループは、以下の資料から要約したものです。 DME 金型仕上げガイド そして オートデスクの金型表面データシート. これらの文献には、異なる、あるいは不完全なRa値の近似マップが掲載されています。数値による粗さ、測定方法、およびサンプルの合格基準については個別に指定してください。グレードラベルは、完成品のRa値を保証する普遍的な基準ではありません。コストおよび耐用年数については、工具ごとに個別に見積もりを依頼する必要があります。

材料と仕上げの組み合わせ:樹脂ごとに適した仕上げは?

金型の仕上げと成形品の外観は、それぞれ異なる仕様です。 樹脂の構造、充填剤、色、および成形条件は、研磨またはテクスチャ加工されたキャビティが部品上でどのように見えるかに影響を与えます。充填樹脂では表面に繊維が見える場合がありますが、単一のBグレードの天井材がすべてのコンパウンドに適用されるわけではありません。1つのグレードがすべての材料で同じ光沢を保証すると仮定するのではなく、代表的な成形サンプルを承認してください。

材料と表面仕上げの適合マトリックスは逆のケースにも当てはまります。つまり、一部の材料は、正常に機能するために特定の最低仕上げレベルを必要とします。 シリコーンやTPEは研磨された表面に非常に強く付着するため、破断することなく離型するには、基本的にB-1以上の表面仕上げが必須となります。POMは摩擦係数が低いため、どのような表面仕上げでも離型性は良好ですが、可動部でのきしみ音を最小限に抑えるためには、キャビティ表面をB-2以上にすることが推奨されます。 オーバーモールド用途では、オーバーモールドの接着に機械的な噛み合わせを確保するため、基材表面はC-1以上、あるいはそれより粗い状態である必要があります。基材表面が研磨されていると、実使用時に剥離故障が発生します。表面仕上げを指定する際は、選択した材料を金型メーカーに伝えてください。そうすれば、鋼材の切削が行われる前に、互換性のない組み合わせについて指摘してもらえます。

  1. すべての図面にSPI仕上げを指定する: キャビティ表面の注記には、必ず仕上げ等級(例:「SPI B-2」または「SPI A-3」)を明記してください。 口頭での指示に頼ったり、工具メーカーのデフォルト設定を前提にしたりしてはいけません。仕上げ仕様が明記されていない場合は、デフォルトで「加工済み状態」となり、Ra 0.8~1.6 μmとなります。
  2. 仕上げを材料の特性に合わせる: GFナイロン製の部品には「A-1」を指定しないでください。ガラス繊維が含まれているため、せいぜい「B-3」が限界となります。仕様書を作成する前に、その材料で達成可能な最高仕上げ度を確認し、そのプラスチックでは再現できない研磨加工に無駄な費用を払うことのないようにしてください。
  3. テクスチャの深さ0.025mmごとに1°のドラフトを追加: SPIのテクスチャグレードがB-1を超える場合は、すべて抜き勾配の補正が必要です。ABSを成形するD-2ブラスト仕上げの金型には、およそ5.5~6°の抜き勾配が必要です。この点を、部品設計図が金型設計者に渡される前に、部品の形状設計に反映させておいてください。
  4. 審美ゾーンと機能ゾーンを分離する: 同じ部品の異なる部位ごとに、仕上げの種類を区別します。例えば、目に見えるA面はB-1とし、B面のリブやボス部分はD-2のままにします。これにより、顧客の目に触れる表面にのみ高品質な研磨を施すことで、キャビティあたり200~400ドルのコスト削減が可能になります。
  5. 表面粗さ測定器を用いて確認する: Ra値は主観的なものではありません。初回製品検査の際には、プロファイル計による測定値を要求してください。 300ドルの携帯型テスターを使えば、工具メーカーが実際にSPI B-1(Ra 0.05~0.10 μm)を納入したのか、それとも「ほぼ同等」とされるB-2(Ra 0.10~0.15 μm)を納入したのかを確認できます。
  6. Budget for Re-Polishing in Tool Life Planning: A-grade finishes lose spec after 50K-100K shots. If your program runs 500K parts, budget for 5-10 re-polish cycles at $300-800 each, and account for the cumulative 0.01-0.05mm of steel removal in your tolerance stack.
Illustrative polished, satin, matte and textured plastic surface sample plaques
Illustrative surface appearances, not calibrated SPI samples. Agree the finish reference and approve a physical sample in the selected resin.

業界別適用マトリックス

産業 Common SPI Grades Typical Material Primary Requirement 検査方法
Optical Components A-1, A-2 PC, PMMA Light transmission >90% Profilometer + haze meter
コンシューマー・エレクトロニクス A-3, B-1 PC/ABS, ABS Premium feel + scratch resistance Visual under 500 lux
自動車の内装 B-2, C-1 PP, PC/ABS Low gloss for glare reduction Gloss meter at 60° angle
産業用ハウジング D-1, D-2 GF Nylon, PC Durability + defect hiding Visual comparison plaques

Cost Decision Framework: SPI Finish Grade Economics

Surface finish directly impacts three cost drivers — initial tooling, cycle time, and maintenance. Here’s how finish grade affects your total cost of ownership across production volumes:

  • Prototype / Bridge Tooling (1-5K parts): Use B-3 or as-machined finish. The $200-500 savings per cavity doesn’t justify premium polishing for low-volume validation. Expect visible tool marks but functional parts.
  • Low-Volume Production (5K-50K parts): B-2 is the sweet spot. One polish cycle lasts the entire production run on P20 steel, and the semi-gloss finish satisfies 90% of consumer product requirements. Total finish cost: $200-400 per cavity, zero re-polish expense.
  • Mid-Volume Production (50K-250K parts): A-3 for cosmetic surfaces, B-2 for everything else. Budget for one re-polish at 150K shots ($400-600). If optical clarity is required, A-1 on the critical surface only — not the entire cavity.
  • High-Volume Production (250K+ parts): Hardened steel (52+ HRC) with A-2 finish for cosmetic, B-1 for functional. Re-polish every 100K-150K shots on hardened steel, 50K-75K on P20. Each re-polish round costs $500-800 per cavity including downtime. Over 1M shots, total finish maintenance can reach $4,000-8,000 per cavity — factor this into your piece price from day one.

A-grade polish costs $30-60/hour for skilled labor. A typical consumer product cavity takes 12-16 hours for A-1, 8-10 hours for A-2, and 4-6 hours for A-3. The labor component alone explains the cost hierarchy — finish grade is literally paid for in hours of a polisher’s time.

Common Surface Finish Defects and Solutions

欠陥 根本原因 解決策
Orange Peel Texture Over-polishing with wrong technique — excessive pressure causes surface waviness instead of smoothness Re-polish using progressive grit steps without skipping grades (400→600→800→1200, never 400→1200). Reduce polishing pressure to 5-10 N and verify with profilometer between steps.
Sink Marks Visible Through Polish High-gloss finish amplifies even 0.005mm of sink (vs 0.02mm threshold on C-grade) Reduce rib thickness to 50% of wall. Increase packing pressure 15-25% and extend hold time 2-3 seconds. If persistent, downgrade to A-3 or B-1 — semi-gloss hides sink 4× better than mirror polish.
Scratch Marks After Short Runs Soft mold steel (below 40 HRC) paired with abrasive material like glass-filled resin Upgrade to hardened steel (48-52 HRC) or stainless (S136 at 50-54 HRC). Apply TiN or CrN coating (0.003-0.005mm) for added abrasion resistance on GF materials. Expect coating to add $300-600 per cavity.
Inconsistent Gloss Across Part Uneven polishing pressure in contoured areas or differential mold temperature during molding Use conformal cooling to maintain mold surface temperature within ±3°C across the cavity. Verify polish uniformity with a gloss meter at multiple positions (aim for ±5 GU variation on A-grade). Re-polish problem areas with specialized contour tools.
Four plastic parts with different SPI finishes for different industry applications

Finish examples, left to right

  • Automotive trim
    SPI A2 · High gloss
  • Medical device housing
    SPI B1 · Semi-gloss
  • Consumer electronics
    SPI C1 · Soft matte
  • Industrial tool housing
    SPI D2 · Textured

These examples illustrate appearance. Confirm the finish against a physical sample in the selected resin.

概要

決断の分かれ目 SPI Finishes 購入者への注意事項
A group 高光沢仕上げ Use when appearance is the priority
B group Paper-prepared finish Balance appearance and tooling cost
C group Ground finish Good for general functional parts
D group Textured / matte Helps hide wear and molding marks

よくある質問

射出成形において、SPIとは何の略ですか?

SPIとは、Society of the Plastics Industry(現在はPLASTICS Industry Association)の略称です。SPIの表面仕上げ規格は、12種類の定義された金型研磨グレード(A-1からD-3)からなるもので、研磨方法、研磨材の種類、およびその結果得られる表面粗さ(Ra)値を規定しています。 世界中の射出成形金型メーカーは、設計図面においてSPI等級を参照し、キャビティの研磨レベル要件を伝えています。この規格は当初「SPI-SPE金型仕上げガイド」として発行され、組織名が変更された後も、事実上の世界標準として現在も用いられています。

What’s the best surface finish for clear polycarbonate parts?

For clear polycarbonate optical components (lenses, light pipes, transparent enclosures), SPI A-1 or A-2 is essential. A-1 delivers Ra 0.012-0.025 μm — true mirror quality — and is required for lenses where any surface imperfection distorts light transmission. A-2 (Ra 0.025-0.05 μm) works well for general transparent housings and covers where minor surface imperfections are tolerable. For non-optical clear parts like protective covers, A-3 often suffices. Keep in mind that PC’s inherent light transmission of 88-92% means no amount of polishing can make it as clear as glass (99%+), and any contamination or moisture in the resin degrades clarity independently of mold finish.

Aグレードの研磨加工は、金型コストにどれくらいの追加費用がかかりますか?

金型や仕上げ要件を確認せずに、キャビティ1つあたりの保険料を確実に固定することはできません。費用は、金型用鋼材や硬度、研磨面積、キャビティ数、部品の形状、初期の表面状態、光学的または外観上の合格基準、手作業による研磨のためのアクセス性、および将来のメンテナンスのしやすさによって変動します。 比較可能な見積もりを得るためには、図面上の各外観ゾーンに印を付け、必要なSPIグレードまたは承認済みサンプルを明記し、樹脂の種類と色を特定した上で、仕上げ作業を金型費用の別項目として請求するように依頼してください。

同じ部品に、異なるSPI仕上げを施すことは可能ですか?

Yes — this is standard practice and strongly recommended for cost optimization. The cavity (A-side, cosmetic face) typically gets the premium finish (B-2 to A-2), while the core side gets a functional finish (C-1 to D-2) since it’s usually hidden from view. On a single drawing, annotate each surface: “SPI B-2 — Cosmetic Face A” and “SPI D-2 — Non-Cosmetic Surfaces” or designate specific zones. The cost savings are substantial — polishing only the visible A-side rather than the entire cavity reduces finishing labor by 40-60%. Just ensure your drawing clearly delineates the finish boundary lines so the toolmaker knows exactly where each finish applies.

関連記事

Request an SPI Finish and Mold Review

Use this review when a drawing calls out an SPI finish, when an appearance sample must be translated into a mold requirement, or when finish choice is affecting release, gloss, visibility of flow marks or tooling cost.

SPIの表面仕上げ基準は、どのようにして明確な金型要件となるのでしょうか?

Assign the required finish to specific drawing zones and provide a physical or approved visual reference where appearance is critical. Identify resin, color, draft, parting line and gate restrictions. The quotation should distinguish mold polishing or texturing from secondary part finishing, and state how molded samples will be approved. An SPI label alone does not guarantee the same appearance in every resin.

  • Appearance target: Requested SPI grade, approved sample or texture reference, gloss target and cosmetic zones.
  • Part and resin: 2D drawing or CAD, resin and color, wall thickness, critical surfaces and expected defects to avoid.
  • Tooling status: New mold, mold modification or production issue, plus cavity count and the current tool stage.
  • Commercial scope: Prototype or production quantity, annual volume, destination and target timing.

このレビューでは、以下の点を特定することができます: a suitable SPI grade or alternative, resin-and-finish compatibility concerns, drawing or sample questions, inspection references and the tooling or molded-part scope that should be quoted.

Mark finish boundaries, mold parting line and gate restrictions; define whether acceptance is visual, a measured texture, gloss, haze or another stated requirement. Agree the reference sample, lighting or measurement method and the sample approval stage.

Final finish selection and pricing depend on the approved appearance reference, resin, mold steel, part geometry, polishing area, cavity count, tool condition and inspection requirement.

Tell Us About Your Part

このフィールドは必須です。.
このフィールドは必須です。.
このフィールドは必須です。.
このフィールドは必須です。.
このフィールドは必須です。.
このフィールドは必須です。.
このフィールドは必須です。.

トップに戻る